# elixir_ale - Elixir Actor Library for Embedded
[![Build Status](https://travis-ci.org/fhunleth/elixir_ale.svg)](https://travis-ci.org/fhunleth/elixir_ale)
`elixir_ale` provides high level abstractions for interfacing to hardware
peripherals on embedded platforms. If this sounds similar to
[Erlang/ALE](https://github.com/esl/erlang-ale), that's because it is. This
library is a Elixir-ized implementation of the library. It does differ from Erlang/ALE
in that the C port side has been simplified and all Raspberry PI-specific code
removed. It still runs on the Raspberry PI, but it interfaces to the hardware
only through Linux interfaces.
# Getting started
If you're natively compiling elixir_ale, everything should work like any other
Elixir library. Normally, you would include elixir_ale as a dependency in your
`mix.exs` like this:
defp deps do
[{:elixir_ale, "~> 0.5.1"}]
end
If you just want to try it out, you can do the following:
git clone https://github.com/fhunleth/elixir_ale.git
cd elixir_ale
mix compile
iex -S mix
If you're cross-compiling, you'll need to setup your environment so that the
right C compiler is called. See the `Makefile` for the variables that will need
to be overridden. At a minimum, you will need to set `CROSSCOMPILE`,
`ERL_CFLAGS`, and `ERL_EI_LIBDIR`.
`elixir_ale` doesn't load device drivers, so you'll need to make sure that any
necessary ones for accessing I2C or SPI are loaded beforehand. On the Raspberry
Pi, the [Adafruit Raspberry Pi I2C
instructions](https://learn.adafruit.com/adafruits-raspberry-pi-lesson-4-gpio-setup/configuring-i2c)
may be helpful.
If you're trying to compile on a Raspberry Pi and you get errors indicated that Erlang headers are missing
(`ie.h`), you may need to install erlang with `apt-get install
erlang-dev` or build Erlang from source per instructions [here](http://elinux.org/Erlang).
# Examples
`elixir_ale` only supports simple uses of the GPIO, I2C, and SPI interfaces in
Linux, but you can still do quite a bit. The following examples were tested on a
Raspberry Pi that was connected to an [Erlang Embedded Demo
Board](http://solderpad.com/omerk/erlhwdemo/). There's nothing special about
either the demo board or the Raspberry Pi, so these should work similarly on
other embedded Linux platforms.
## GPIO
A GPIO is just a wire that you can use as an input or an output. It can only be
one of two values, 0 or 1. A 1 corresponds to a logic high voltage like 3.3 V
and a 0 corresponds to 0 V. The actual voltage depends on the hardware.
Here's an example setup:
![GPIO schematic](assets/images/schematic-gpio.png)
To turn on the LED that's connected to the net labelled
`PI_GPIO18`, you can run the following:
iex> {:ok, pid} = Gpio.start_link(18, :output)
{:ok, #PID<0.96.0>}
iex> Gpio.write(pid, 1)
:ok
Input works similarly:
iex> {:ok, pid} = Gpio.start_link(17, :input)
{:ok, #PID<0.97.0>}
iex> Gpio.read(pid)
0
# Push the button down
iex> Gpio.read(pid)
1
If you'd like to get a message when the button is pressed or released, call the
`set_int` function. You can trigger on the `:rising` edge, `:falling` edge or
`:both`.
iex> Gpio.set_int(pid, :both)
:ok
iex> flush
{:gpio_interrupt, 17, :rising}
{:gpio_interrupt, 17, :falling}
:ok
## SPI
A SPI bus is a common multi-wire bus used to connect components on a circuit
board. A clock line drives the timing of sending bits between components. Bits
on the `MOSI` line go from the master (usually the processor running Linux) to
the slave, and bits on the `MISO` line go the other direction. Bits transfer
both directions simultanteously. However, much of the time, the protocol used
across the SPI bus has a request followed by a response and in these cases, bits
going the "wrong" direction are ignored.
The following shows an example ADC that reads from either a temperature sensor
on CH0 or a potentiometer on CH1.
![SPI schematic](assets/images/schematic-adc.png)
The protocol for talking to the ADC is described in the [MCP3203
Datasheet](http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en010532).
Sending a 0x64 first reads the temperature and sending a 0x74 reads the
potentiometer.
# Make sure that you've enabled or loaded the SPI driver or this will
# fail.
iex> {:ok, pid} = Spi.start_link("spidev0.0")
{:ok, #PID<0.124.0>}
# Read the potentiometer
# Use binary pattern matching to pull out the ADC counts (low 12 bits)
iex> <<_::size(4), counts::size(12)>> = Spi.transfer(pid, <<0x74, 0x00>>)
<<1, 197>>
iex> counts
453
# Convert counts to volts (1023 = 3.3 V)
iex> volts = counts / 1023 * 3.3
1.461290322580645
## I2C
An I2C bus is similar to a SPI bus in function, but uses fewer wires. It
supports addressing hardware components and bidirectional use of the data line.
The following shows a bus IO expander connected via I2C to the processor.
![I2C schematic](assets/images/schematic-i2c.png)
The protocol for talking to the IO expander is described in the [MCP23008
Datasheet](http://www.microchip.com/wwwproducts/Devices.aspx?product=MCP23008).
Here's a simple example of using it.
# On the Raspberry Pi, the IO expander is connected to I2C bus 1 (i2c-1).
# Its 7-bit address is 0x20. (see datasheet)
iex> {:ok, pid} = I2c.start_link("i2c-1", 0x20)
{:ok, #PID<0.102.0>}
# By default, all 8 GPIOs are set to inputs. Set the 4 high bits to outputs
# so that we can toggle the LEDs. (Write 0x0f to register 0x00)
iex> I2c.write(pid, <<0x00, 0x0f>>
:ok
# Turn on the LED attached to bit 4 on the expander. (Write 0x10 to register
# 0x09)
iex> I2c.write(pid, <<0x09, 0x10>>)
:ok
# Read all 11 of the expander's registers to see that the bit 0 switch is
# the only one on and that the bit 4 LED is on.
iex> I2c.write(pid, <<0>>) # Set the next register to be read to 0
:ok
iex> I2c.read(pid, 11)
<<15, 0, 0, 0, 0, 0, 0, 0, 0, 17, 16>>
# The operation of writing one or more bytes to select a register and
# then reading is very common, so a shortcut is to just run the following:
iex> I2c.write_read(pid, <<0>>, 11)
<<15, 0, 0, 0, 0, 0, 0, 0, 0, 17, 16>>
# The 17 in register 9 says that bits 0 and bit 4 are high
# We could have just read register 9.
iex> I2c.write_read(pid, <<9>>, 1)
<<17>>
# License
This library draws much of its design and code from the Erlang/ALE project which
is licensed under the Apache License, Version 2.0. As such, it is licensed
similarly.