# NervesSSH
[](https://circleci.com/gh/nerves-project/nerves_ssh/tree/main)
[](https://hex.pm/packages/nerves_ssh)
Manage an SSH daemon and its subsystems on Nerves devices. It has the following
features:
1. Automatic startup of the SSH daemon on initialization
2. Ability to hook the SSH daemon into a supervision tree of your choosing
3. Easy setup of SSH firmware updates for Nerves
4. Easy shell and exec setup for Erlang and Elixir
5. Some protection from easy-to-make mistakes that would cause ssh to not be
available
## Usage
This library wraps Erlang/OTP's [SSH
daemon](http://erlang.org/doc/man/ssh.html#daemon-1) to make it easier to use
reliably with Nerves devices.
Most importantly, it makes it possible to segment failures in other OTP
applications from terminating the daemon and it recovers from rare scenarios
where the daemon terminates without automatically restarting.
It can be started automatically as an OTP application or hooked into a
supervision tree of your creation. Most Nerves users start it automatically as
an OTP application. This is easy, but may be limiting and it requires that you
use the application environment. See the following sections for options:
### Starting as an OTP application
If you're using [`:nerves_pack`](https://hex.pm/packages/nerves_pack) v0.4.0 or
later, you don't need to do anything except verify the `:nerves_ssh`
configuration in your `config.exs` (see below). If you are not using
`:nerves_pack`, add `:nerves_ssh` to your `mix` dependency list:
```elixir
def deps do
[
{:nerves_ssh, "~> 0.1.0", targets: @all_targets}
]
end
```
And then include it in `:shoehorn`'s `:init` list:
```elixir
config :shoehorn,
init: [:nerves_runtime, :vintage_net, :nerves_ssh]
```
`:nerves_ssh` will work if you do not add it to the `:init` list. However, if
your main OTP application stops, OTP may stop `:nerves_ssh`, and that would make
your device inaccessible via SSH.
### Starting as part of one of your supervision trees
If you want to do this, make sure that you do NOT specify `:nerves_ssh` in your
`config.exs`. The `:nerves_ssh` key decides whether or not to automatically launch
based on this.
Then when specifying the children for your supervisor, add `NervesSSH` like
this:
```elixir
{NervesSSH, nerves_ssh_options}
```
The `nerves_ssh_options` should be a `NervesSSH.Options` struct. See the
`Configuration` section option fields that you may specify. Calling
`NervesSSH.Options.with_defaults(my_options_list)` to build the
`nerves_ssh_options` value is one way of getting reasonable defaults.
## Configuration
NervesSSH supports the following configuration items:
* `:authorized_keys` - a list of SSH authorized key file string
* `:user_passwords` - a list of username/password tuples (stored in the
clear!)
* `:port` - the TCP port to use for the SSH daemon. Defaults to `22`.
* `:subsystems` - a list of [SSH subsystems specs](https://erlang.org/doc/man/ssh.html#type-subsystem_spec) to start. Defaults to SFTP and `ssh_subsystem_fwup`
* `:system_dir` - where to find host keys
* `:shell` - the language of the shell (`:elixir`, `:erlang`, or `:disabled`). Defaults to `:elixir`.
* `:exec` - the language to use for commands sent over ssh (`:elixir`, `:erlang`, or `:disabled`). Defaults to `:elixir`.
* `:iex_opts` - additional options to use when starting up IEx
* `:daemon_option_overrides` - additional options to pass to `:ssh.daemon/2`. These take precedence and are unchecked.
## Authentication
It's possible to set up a number of authentication strategies with the Erlang
SSH daemon. Currently, only simple public key and username/password
authentication setups are supported by `:nerves_ssh`. Both of them work fine for
getting started. As needs become more sophisticated, you can pass options to
`:daemon_option_overrides`.
### Public key authentication
Public ssh keys can be specified so that matching clients can connect. These
come from files like your `~/.ssh/id_rsa.pub` or `~/.ssh/id_ecdsa.pub` that were
created when you created your `ssh` keys. If you haven't done this, the
following
[article](https://help.github.com/articles/generating-a-new-ssh-key-and-adding-it-to-the-ssh-agent/)
may be helpful. Here's an example that uses the application config:
```elixir
config :nerves_ssh,
authorized_keys: [
"ssh-rsa
AAAAB3NzaC1yc2EAAAADAQABAAAAgQDBCdMwNo0xOE86il0DB2Tq4RCv07XvnV7W1uQBlOOE0ZZVjxmTIOiu8XcSLy0mHj11qX5pQH3Th6Jmyqdj",
"ssh-rsa
AAAAB3NzaC1yc2EAAAADAQABAAACAQCaf37TM8GfNKcoDjoewa6021zln4GvmOiXqW6SRpF61uNWZXurPte1u8frrJX1P/hGxCL7YN3cV6eZqRiF"
]
```
Here's another way that may work well for you that avoids needing to commit your
keys:
```elixir
config :nerves_ssh,
authorized_keys: [
File.read!(Path.join(System.user_home!, ".ssh/id_rsa.pub"))
]
```
### Username/password authentication
The SSH console uses public key authentication by default, but it can be
configured for usernames and passwords via the `:user_passwords` key. This
has the form `[{"username", "password"}, ...]`. Keep in mind that passwords are
stored in the clear. This is not recommended for most situations.
```elixir
config :nerves_ssh,
user_passwords: [
{"username", "password"}
]
```
## Goals
* [X] Support public key authentication
* [X] Support username/password authentication
* [ ] Device generated server certificate and key
* [ ] Device generated username/password
