# Raspberry Pi 2 Model B
This is the base Nerves System configuration for the Raspberry Pi 2 Model B.
![Fritzing Raspberry Pi 2 image](assets/images/raspberry-pi-2-model-b.png)
| Feature | Description |
| -------------------- | ------------------------------- |
| CPU | 900 MHz quad-core ARM Cortex-A7 |
| Memory | 1 GB DRAM |
| Storage | MicroSD |
| Linux kernel | 4.4 w/ Raspberry Pi patches |
| IEx terminal | HDMI and USB keyboard (can be changed to UART) |
| GPIO, I2C, SPI | Yes - Elixir ALE |
| ADC | No |
| PWM | Yes, but no Elixir support |
| UART | 1 available - `ttyAMA0` |
| Camera | Yes - via rpi-userland |
| Ethernet | Yes |
| WiFi | Requires USB WiFi dongle |
| Bluetooth | Not supported |
The most common way of using this Nerves System is create a project with `mix
nerves.new` and to export `MIX_TARGET=rpi2`. See the [Getting started
for more information.
If you need custom modifications to this system for your device, clone this
repository and update as described in [Making custom
If you're new to Nerves, check out the
project for creating a starter project. It will get you started with the basics
like bringing up networking, initializing the writable application data
partition, and enabling ssh-based firmware updates. It's easiest to begin by
using the wired Ethernet interface 'eth0' and DHCP.
## Supported USB WiFi devices
The base image includes drivers and firmware for Ralink RT53xx
(`rt2800usb` driver), RealTek RTL8712U (`r8712u` driver) and
RealTek RTL 8192 (`rtl8192cu` driver) devices (e.g. Edimax USB WiFi dongles).
We are still working out which subset of all possible WiFi dongles to
support in our images. At some point, we may have the option to support
all dongles and selectively install modules at packaging time, but until
then, these drivers and their associated firmware blobs add significantly
to Nerves release images.
If you are unsure what driver your WiFi dongle requires, run Raspbian and configure WiFi
for your device. At a shell prompt, run `lsmod` to see which drivers are loaded.
Running `dmesg` may also give a clue. When using `dmesg`, reinsert the USB
dongle to generate new log messages if you don't see them.
## Provisioning devices
This system supports storing provisioning information in a small key-value store
outside of any filesystem. Provisioning is an optional step and reasonable
defaults are provided if this is missing.
Provisioning information can be queried using the Nerves.Runtime KV store's
Keys used by this system are:
Key | Example Value | Description
:--------------------- | :---------------- | :----------
`nerves_serial_number` | "1234578"` | By default, this string is used to create unique hostnames and Erlang node names. If unset, it defaults to part of the Raspberry Pi's device ID.
The normal procedure would be to set these keys once in manufacturing or before
deployment and then leave them alone.
For example, to provision a serial number on a running device, run the following
iex> cmd("fw_setenv nerves_serial_number 1234")
This system supports setting the serial number offline. To do this, set the
`NERVES_SERIAL_NUMBER` environment variable when burning the firmware. If you're
programming MicroSD cards using `fwup`, the commandline is:
sudo NERVES_SERIAL_NUMBER=1234 fwup path_to_firmware.fw
Serial numbers are stored on the MicroSD card so if the MicroSD card is
replaced, the serial number will need to be reprogrammed. The numbers are stored
in a U-boot environment block. This is a special region that is separate from
the application partition so reformatting the application partition will not
lose the serial number or any other data stored in this block.
Additional key value pairs can be provisioned by overriding the default provisioning.conf
file location by setting the environment variable
`NERVES_PROVISIONING=/path/to/provisioning.conf`. The default provisioning.conf
will set the `nerves_serial_number`, if you override the location to this file,
you will be responsible for setting this yourself.
## Linux kernel and RPi firmware/userland
There's a subtle coupling between the `nerves_system_br` version and the Linux
kernel version used here. `nerves_system_br` provides the versions of
`rpi-userland` and `rpi-firmware` that get installed. I prefer to match them to
the Linux kernel to avoid any issues. Unfortunately, none of these are tagged
by the Raspberry Pi Foundation so I either attempt to match what's in Raspbian
or take versions of the repositories that have similar commit times.
[Image credit](#fritzing): This image is from the [Fritzing](http://fritzing.org/home/) parts library.